Skip to main content
Version: 1.5.X

Archiving and Restoring a Database

This documentation describes processes for the compression and decompression of a Casper node database and streaming from a backup location.

Zstandard is the best method for compression speed and space for the current LMDB-based database system that the casper-node uses.

note

The values presented in this document assume that the trie-compact tool was run on a Mainnet database for compression. Contact the support team if you have questions.

Zstandard Limitations

The current DB implementation uses sparse files, which can be partially empty, thus not being processed efficiently. You can use tar as a pre-filter for stripping sparse data, as shown here, thus eliminating the need to read the full DB size and improving processing.

Zstandard Installation

To install Zstandard, run the following command:

sudo apt install zstd

Note that Zstandard version 1.4.4 is distributed with Ubuntu 20.04, while version 1.3.3 is distributed with Ubuntu 18.04. Later versions have more documentation.

Initial Warnings

You need to stop the casper-node-launcher process of the node (and, therefore, the casper-node process using the DB) before any compression or decompression into a location. Otherwise, strange things can and will occur.

Compression

Run the following basic tar command from the DB directory. For Mainnet, the directory would be /var/lib/casper/casper-node/casper, and for Testnet it would be /var/lib/casper/casper-node/casper-test.

tar -cv --sparse .

On some systems, you may get better performance if you specify the block number as an argument:

tar -b 4096 -cv --sparse .

You can then stream the result into zstd. The sections below discuss the level, thread count, and long arguments.

tar -b 4096 -cv --sparse . | zstd -[level] -cv -T[thread count] --long=31 > [path_to]/file.tar.zst

Compression level

The -[level] argument is the compression level from 1 to 19 (and 20-22 with expansion). In testing, we found 15 to be the sweet spot in compression time vs. size. We recommend lower compression if you plan to transfer the archive only once. If you are creating an archive to be downloaded by many, then the extra time for higher compression may be helpful.

Here are some examples of a Mainnet DB compression at block 741160:

LevelTime (min:sec)Size
1229:2015.8 GB
1546:1513.0 GB
1787:4213.0 GB
19197:0812.9 GB

For local backups, using 1-5 is a great compression speed-to-size trade-off.

Thread count

The -T[thread count] is the number of threads that zstd should use for compression. If running a script or command on varying machines, use T0 to allow zstd to detect the number of cores and run with the same number of threads as the detected cores. A speed-up can be obtained for machines with multiple threads per core by configuring a thread count near the number of threads. It is advisable to stay within the number of CPU threads. The recommendations in this article will use -T0.

Long-distance matching

The --long=31 argument is where we see the most space gained by the algorithm because it controls the size of the matching window in powers of 2 (2**31 is 2 GB). The downside is that it requires 2.0 GB memory during compression and decompression as it looks and rebuilds ahead. The default is 27 or 128 MB.

At compression 19, we see a 30 GB file using the default 128 MB look ahead, and a 13 GB file using 2 GB look ahead. Since all validators should have 16-32 GB of memory, we keep this at --long=31.

An important note is that decompression requires a compatible argument. Trying with a different long-distance matching value will result in an error. However, it will also return the necessary value to provide.

Summary of commands

The general command for compression is:

tar -b 4096 -cv --sparse . | zstd -15 -cv -T0 --long=31 > [path_to]/file.tar.zst

For local backups, use a lower compression level:

tar -b 4096 -cv --sparse . | zstd -5 -cv -T0 --long=31 > [path_to]/file.tar.zst

Decompression

zstd -d is the command for decompression; however, the same --long value used for compression must be specified. For all casper-node DB-related decompression, you will likely use this command:

zstd -cd --long=31 <.tar.zst file>

If --long=31 is omitted, you might see an error such as this, which also gives you the solution:

./casper.tar.zst : Decoding error (36) : Frame requires too much memory for decoding 
./casper.tar.zst : Window size larger than maximum : 2147483648 > 134217728
./casper.tar.zst : Use --long=31 or --memory=2048MB

You can then use the zstd result to populate a tar -xv command. Also, create the decompressed files using sudo -u casper, because the files will be used by the casper-node. Run the following command inside an empty DB location:

zstd -cd --long=31 <.tar.zst file> | sudo -u casper tar -xv

To fix ownership, use this command:

sudo /etc/casper/node_util.py fix_permissions

Streamed Decompression

If a .tar.zst archive is hosted on a website and you will not need the file after decompressing, you can stream it into the process using curl, which can output to stdout with --output and stream binary to your terminal.

curl -s --output - <URL for tar.zstd file>

If you use the output along with the previous process, you can decompress the files from curl directly into a local directory:

curl -s --output - <tar.zst URL> | zstd -d --long=31 | sudo -u casper tar -xv

Starting a New Node with a Decompressed DB

If you are starting a node with a decompressed DB, you must tell the node to run at the protocol version of the tip of your DB. You can do this most efficiently with the node_util.py script included in the casper-node-launcher installation.

For example, if you are using a DB archive from node version 1.4.5, you would run this command:

sudo /etc/casper/node_util.py force_run_version 1_4_5